Measure the window’s width and height several times to ensure you get the correct size for the blinds. When installed, accurate measurements matters the blinds fit well, operate well and look neat.
Measuring for blinds seems simple but a small mistake can affect the end result. Before ordering blinds, homeowners, offices, hotels and commercial spaces need to measure the window width, height, frame depth, wall space and the type of fitting needed.
For best result, we recommended professional in-house measurement to avoid size errors, uneven gaps, light leakage and installation problems.
What Are the Basic Checklist for Measuring Blinds for Windows?
The basic checklist for measuring blinds includes choosing an inside or outside mount. Measure the window width and height at different points. Check the frame depth. Look for handles, grills, curtain rods, or other obstacles that may affect blind installation and operation.
Step 1: Decide Inside Mount or Outside Mount
There are usually two methods of fitting blinds:
Inside mount: The blind is mounted on the inside of the window frame. This helps to give a neat and clean built in look. The window frame needs to be deep enough.
Outside mount: The blind is mounted outside the window frame, often on the wall or the ceiling. good for uneven, shallow window frames or to add privacy or light control.
Step 2: Measuring Inside Mount Blind
To install inside mount blinds, begin measuring by the width of the window opening at three points: the top, middle and bottom. Since windows are not always perfectly square; even if they look perfect to the eye! Use the narrowest of these width measurements when ordering your blinds.
Next, measure the height on the left side, in the center, and on the right side of the window. Write down the longest height measurement to ensure full coverage. Note the maximum height measurement to cover the entire area.
Finally check the depth of the window recess to allow enough space for the blind mechanism. Remember, different styles of blind have different minimum depths, so always consult the manufacturer’s specs before ordering.
Step 3: Measure for Outside-Mount Blinds
For outside-mount blinds, measure the area you want covered by the blinds, not just the window itself. It is a good idea to add a few 2–4 inches (5–10 cm) on both sides of the window so that less light comes in and you get better privacy.
For the height, measure from where you plan to fix the blinds above the window down to the point where you want them to end. Always make sure there is enough space on the wall to install the brackets properly.
Step 4: Check Handles, Grills, and Obstacles
Window handles, grills, curtain rods, ac pipes, switches or projections on the wall can affect blind movement. These should be checked during measurement so that the blind does not jam when opening or closing.
Why Professional Measurement Matters
The blinds will be the right size and will be professionally measured. Blinds can be too small, too big or not fit properly on the sides due to incorrect measurements. A professional can also tell you if an inside or outside mount will be better for your window and room.
This is especially useful for large windows, office cabins, hotel rooms, balconies, glass partitions and commercial spaces where a lot of blinds are needed to look neat and match each other.
A furnishing expert during a site visit checks the window size, frame depth, wall condition, available fitting space, window handles, grills, curtain rods and other obstacles.
They also consider the amount of sunlight that enters the room and the amount of privacy you need. From these checks they can recommend the best type of blinds for comfortable everyday use.
What Are the Common Mistakes to Avoid While Measuring?
Always take measurements for each width and height twice.
1. Use a steel tape measure, not a cloth one. Steel tapes are more accurate and less likely to stretch or bend than plastic tapes.
2. And always write down the correct value, no rounding up or down.
3. Measure each window individually even if they appear identical.
4. Look for any obstacles such as window handles, cranks or air-conditioning units that may get in the way of the blinds.
5. Leave enough space for the blinds to move up or down, and tilt without hitting handles, trims or other fittings around the window.
Why Choose Shiv Furnishing for Blinds Installation?
If you are interested in premium custom blinds, Shiv Furnishing can assist you in product selection, window measurement and professional installation.
They provide in-house measurement services so you can be confident that the blinds you pick will fit your windows perfectly. They check the window size, the fit specifications and other important points before fitting it. It avoids fitting problems and reduces the risks of errors that are costly.
Whatever type of blinds you choose for your windows, it is important to take the measurements accurately for a neat finish, better control of light, enhanced privacy and smooth operation.
Professional measurement and fitting saves time and reduces the chances of error ensuring the blinds look neat and fit well at homes, offices, hotels and commercial areas.
Key Takeaways
The key to good blind installation is accurate measurements of the window. Careful measuring means the blinds fit well, look good and work well.
If you are not confident about measuring yourself, you could consider professional measuring and installation services to avoid mistakes and get the best results.
